ULMA HYDROPLUS Mini w/ Iron Age IA-ANISE-0520-HP Anise Heel Proof Cast Iron Grate | Class B

SKU: HYDROM-IA-ANISE-HP

Kit includes channel section(s), grate(s), 2 end caps, locking devices

$379.62$4,225.88

New from ULMA, the HYDROPLUS Mini is a shallow neutral trench drain for pedestrian and occasional car traffic for areas of low hydraulic requirements. Polypropylene channel externally measures 132mm wide, internal width of 100mm and overall height 84mm and 1 meter in length. Compatible with the same full line of grates as offered for the ULMA polymer concrete channels, this system offers a wide variety of options. Although the grates are listed as a load class B, this system is rated as A, or B depending upon installation.

ULMA HYDROPLUS Mini
Diagrams are located on the bottom of the channel to assist with installation and custom cuts. Raised notches allow for proper saw alignment for cutting angles as well as straight section cuts.
  • Modular design offers the flexibility of two bottom outlet knockout options for pipe connections
  • Two side knockouts can be used as ‘open’ outlets or connected to other channels to create a tee or right and left 90-degree bends
  • Every 10cm, the channel is molded on the bottom to allow for cuts to make, providing a natural coupler that will slide into that female section of the next channel
  • The bottom of each channel contains diagrams for cutting, installation as well as cutting angles
  • Channels conveniently feature raised notches that assist in properly aligning saws for diagonal cuts when fabricating angles
  • Side cut-out area allows for 90-degree assembly of channels if the project requires

Load class ratings for entire systems will always be determined by the lowest class within the system. For example, if the channel is rated as a C and the grate is rated as a D, the overall system will be rated as load class C. The same is true should the channel be rated as load class C and the grates are rated as load class A; the system as a whole would be rated as load class A.

HYDROPLUS Mini Kit Includes:

  • 1M (3.3 ft) polypropylene channel sections
  • Cast Iron Grate (item# IA-ANISE-0520-HP) 124mm x 497mm; Qty.2 grates per 1M channel section
  • Qty.2, closed-end caps per kit
  • Two locking bolts (LD100MX-3) per 1M channel section

ULMA Hydro Plus Mini Drawing

Cast Iron Grate (IA-ANISE-0520-HP) is rated as a Load Class B, and measures 19.56″ x 4.81″. (There may be slight dimension variances on cast iron products)

2 grates per 1M channel section. Channels are marked to aid in cutting to 0.5M length if needed.

Please note that all raw cast-iron grates begin to naturally rust with exposure to any form of moisture and will appear bright orange before settling to brown.

Specification Sheet for IA-ANISE-0520-HP Grate

CLICK HERE for HYDROPLUS Mini Installation Instructions

CLICK HERE for ULMA Declaration of Conformity

NOTE: For proper installation, grates must be in the channel during installation.

Your #1 Trench Drain Supply Resource!

Application

Animal and Zoo, Driveway Drainage, Greenhouse, Municipal, Patio, Pool and Spa, Poolside, Residential

Channel Material

Plastic

Product Type

Drainage Kit

Load Class

Load Class B

Channel Type

Neutral

Grate Width

5 inch

Manufacturer

TDS, ULMA

Grate Material

System

HYDROPLUS MINI

Grate Finish

,

Grate Pattern

Grate Length

Finish Type

,

CSI Code 22 00 00, 22 14 00, 22 14 26, 22 14 26.19, 33 30 00, 33 40 00, 33 44 00, 33 44 13, 33 44 16, 33 46 13
SHARE YOUR CART